Схема проезда
График работы
пн–пт: с 09:30 до 18:30
Кронштадтский бульвар 7

Коды ошибок устройств Kyocera Mita

Коды ошибок устройств Kyocera Mita
Коды ошибок устройств Kyocera Mita

Предлагаем ознакомиться с кодами ошибок принтеров и МФУ Kyocera Mita. В данной публикации приведены ошибки популярных моделей копировальных аппаратов Kyocera Mita и причины их возникновения.

В случае появления серьезной неисправности, мы не рекомендует проводить ремонт принтера самостоятельно, а советуем обратиться в наш сервисный центр Прионта, где квалифицированные мастера справятся с любой поставленной им задачей.

KYOCERA MITA 1560

  • 01 Exiting simulation mode
  • 02 copiing without paper
  • 05 Enabling ADF operation without originals
  • 06 checking ADF operation
  • 09 Setting shipping defaults
  • 10 main motor on
  • 11 checking switch operation
  • 12 checking solenoid operation
  • 16 checking for skewed paper feed with test copies
  • 27 adjusting leading edje registration timing
  • 52 adj ADF leading edje
  • 54 adj the leading edje marjin
  • 55 adjusting the side erasure
  • 59 adj the trailing edje blank cut
  • 20 turning the halogen lamp on
  • 21 checking scanning operation
  • 22 adj the AE
  • 23 turn the lens motor on
  • 24 setting the exposure amount
  • 25 adj lateral magnification
  • 26 adj longitudinal magnification
  • 28 setting the lens unit rank
  • 29 adj exposure amount for enlargement/reduction mode
  • 31 setting transfer voltage
  • 32 setting the drum potential
    1. Enter 32 with the numeric keys
    2. Press the print key
    3. Select the output condition: N-output - Normal mode, P-output - Photo (Half tone)
    4. Press the enter key. Main charging starts under the selected output condition; the drive motor, cleaning lamp turn on & developing bias are generated
    5. Press the stop/clear key to stop main charging

  • 42 making a blank lamp copy
  • 46 setting the fixing temperature
  • 47 setting the fixing preheat temperature
  • 50 lighiting all the indicators
  • 60 initialiazing the toner control level
    Loading developer (to be run during machine setup or when developer is replaced):
    1. Enter 60 with the numeric keys
    2. Press the print key
    3. Press the prin key. Aging starts and, after 3 minutes, the following data are automatically set for initial starter developer. Drive then stops. The toner replenisning level (Sim.65) is updated, & developer count (Sim.73) & drive time (Sim.62) data are cleared
    4. Press the stop/clear key

  • 61 forcing toner feed
    1. Enter 61 with the numeric keys
    2. Press the print key. Aging starts and the toner is replenished until the toner sensor output level reaches the toner-repleneshing-off level
    3. Press the stop/clear key

  • 62 adj the toner sensor control voltage
    1. Enter 62 with the numeric keys
    2. Press the print key.The current setting is shown
    3. Change the setting
    4. Press the print key. The setting is stored
    5. Press the stop/clear key

  • 70 initialiazing the backup memory
  • 71 setting the maintenance cycle
  • 72 checking/clearing the maintenance count
  • 73 checking/clearing service call records
  • 74checking/clearing jam counts
  • 76 checking/clearing the service call counts
  • 77 checking/clearing the paper feed counts
  • 80 selecting between double/single counts
  • 81 setting initial exposure mode
  • 82 selecting between manual/auto modes
  • 83 selecting the exposure scale
  • 84 setting the auto clear time
  • 85 setting the auto preheat time
  • 86 setting the auto shutoff time
  • 89 setting the maximum preset number of copies
  • 91 setting operation under the toner empty condition
  • 92 selecting between auto start on/off
  • 93 setting the destination
  • 98 setting the optical section fan motor control

Вход в сервис: 10871087 с клавиатуры.

KYOCERA MITA 1001

  • C1 Paper feed problem
  • C3 Scanner problem
  • C6 Heat problem
  • PF C6 more than 6 times

KYOCERA MITA 111, 111C, 113

  • C1 Drive
  • C5 Charge corona
  • C6 Transfer/separator corona
  • C7 Heat
  • OP Toner hopper lid

KYOCERA MITA 114

  • C2 Main drive
  • C3 Scan
  • C5 Corona
  • C6 Heat

KYOCERA MITA 1205

  • C3 Scan
  • C6 Fuser

KYOCERA MITA 1256

  • AP CC50. Toner being mixed
  • C01 Memory problem. Main board or simulation 70 required
  • C02 EEPROM or main board
  • C21 Drive problem (CC50/1256)
  • C30 Scan
  • C40 Lens drive
  • C61 Fuser problem. No heat or open circuit
  • C63 Fuser thermistor open
  • C64 Fuser thermistor. Short or high fuser temperature
  • C72 1256 drum thermistor open
  • C73 1256 drum thermistor shorted
  • C74 CC50/1256 Developer unit fuse. May have to replace developer unit. Problem at setup
  • C74 1257 Developer thermistor
  • C75 CC50/1256 Drum unit switch problem or drum setup problem
  • C75 1257 developer thermistor
  • C76 May not apply to CC50 or 1256, except if metric. Waste toner full. Reset with simulation 78
  • J01 Feed jam
  • J02 Drum or fuser area jam
  • J03 Jam
  • OF 1256 drum & developer units must be replaced
  • OP Front door open
  • PE/PF No paper, no paper feed problem
  • U1 Total counter
  • Ub CC50. Old developer unit and new drum. Can be reset by replacing the fuse, or by turning the drum one full revolution
  • Uc CC50. New developer unit and old drum. On rear of drum is drum lock. Inside the opening is a white plastic that snaps down after the unit is installed. Remove this rear cover and snap the white plastic blocker back up
  • UF Toner or developer not installed properly

KYOCERA MITA 1257

  • AP CC50. Toner being mixed
  • C01 Memory problem. Main board or simulation 70 required
  • C02 EEPROM or main board
  • C21 Drive problem (CC50/1256)
  • C30 Scan
  • C40 Lens drive
  • C61 Fuser problem. No heat or open circuit
  • C63 Fuser thermistor open
  • C64 Fuser thermistor. Short or high fuser temperature
  • C72 1256 drum thermistor open
  • C73 1256 drum thermistor shorted
  • C74 CC50/1256 Developer unit fuse. May have to replace developer unit. Problem at setup
  • C74 1257 Developer thermistor
  • C75 CC50/1256 Drum unit switch problem or drum setup problem
  • C75 1257 developer thermistor
  • C76 May not apply to CC50 or 1256, except if metric. Waste toner full. Reset with simulation 78
  • J01 Feed jam
  • J02 Drum or fuser area jam
  • J03 Jam
  • OF 1256 drum & developer units must be replaced
  • OP Front door open
  • PE/PF No paper, no paper feed problem
  • U1 Total counter
  • Ub CC50. Old developer unit and new drum. Can be reset by replacing the fuse, or by turning the drum one full revolution
  • Uc CC50. New developer unit and old drum. On rear of drum is drum lock. Inside the opening is a white plastic that snaps down after the unit is installed. Remove this rear cover and snap the white plastic blocker back up
  • UF Toner or developer not installed properly

KYOCERA MITA 1355

  • AP Toner being mixed
  • C01 Memory problem. Main board or simulation 70 required
  • C02 EEPROM or main board
  • C21 Drive problem
  • C30 Scan, motor, switch
  • C40 Lens drive
  • C61 Fuser problem. No heat or open circuit
  • C63 Fuser thermistor open
  • C64 Fuser thermistor open
  • C72 Drum thermistor open. Blank lamps
  • C73 Drum thermistor shorted
  • C74 Developer thermistor
  • C75 Drum unit switch problem or drum setup problem
  • C76 Waste toner full, reset with simulation 78
  • J01 Feed jam
  • J02 Drum or fuser area jam
  • J03 Jam
  • OF Drum & developer units must be replaced (entire process unit)
  • OP Front door open
  • PE/PF No paper or paper feed problem
  • U1 Total counter
  • Ub Old developer unit and new drum. Might be upset by replacing the fuse, or by turning the drum through one full revolution
  • Uc New developer unit and old drum. On rear drum is a lock. Inside the opening is a white plastic that snaps down after the unit is installed. Remove this rear cover and snap the white plastic blocker back up
  • UF Toner or developer not installed properly. Bad toner sensor

KYOCERA MITA 1415

  • C3 Scan problem
  • C6 Fuser problem. Temperature too low, too high, open thermistor. Heat lamp, thermofuse, thermistor, etc
  • PE Paper empty

KYOCERA MITA 142RE

  • C1 Drive
  • C2 Optics
  • C5 Main corona
  • C6 Transfer/separator corona
  • C7 Heat, thermistor, thermofuse

KYOCERA MITA 1435

  • C01 Battery or main board. Simulation 70 might clear
  • C30 Scan problem
  • C31 Scan problem
  • C32 Scan reverse problem
  • C40 Lens motor
  • C5 Lamp Problem
  • C61 Low fuser temperature. Heat lamp, thermofuse
  • C62 Low fuser temperature
  • C63 Fuser thermistor
  • C64 High fuser temperature. Triac, pinched wire
  • C73 Shorted DV unit thermistor
  • PE Paper empty

KYOCERA MITA 1455

  • C01 Battery or main board. Simulation 70 might clear
  • C30 Scan problem
  • C31 Scan problem
  • C32 Scan reverse problem
  • C40 Lens motor
  • C61 Low fuser temperature. Heat lamp, thermofuse
  • C62 Low fuser temperature
  • C63 Fuser thermistor
  • C64 High fuser temperature. Triac, pinched wire
  • C73 Shorted DV unit thermistor
  • PE Paper empty

KYOCERA MITA 152Z

  • C2 Drive section
  • C4 Lens unit
  • C5 Corona
  • C6 Heater

KYOCERA MITA 1560

  • C01 NVRAM problem
  • C20 Main drive problem
  • C30 Scan problem. Scan sensors, scan motor, belt tension, cable tension, etc
  • C40 Lens motor problem, lens sensor motor
  • C50 Corona problem: Broken wire, shorted blocks, bad corona, high voltage transformer
  • C61 Low fuser temperature. Problem with heat lamp, connections, thermal switch, thermistor or main board
  • C63 Open fuser thermistor
  • C64 Shorted fuser thermistor
  • C72 Open drum thermistor
  • C73 Shorted drum thermistor
  • C74 Open external thermistor
  • C75 Shorted external thermistor
  • C90 Communication problem between copier and ADF
  • J30 Jam in registration area
  • J40 Jam inside machine or fuser
  • J50 Exit jam or fuser jam
  • PF Paper feed

Возврат к списку

Заказать звонок