Схема проезда
График работы
пн–пт: с 09:30 до 18:30
Кронштадтский бульвар 7

Коды ошибок принтера Ricoh

Коды ошибок принтера Ricoh

Здесь приведены наиболее часто встречающиеся коды ошибок принтера Ricoh. В данном разделе приведены ошибки популярных моделей принтеров и МФУ Ricoh и причины их возникновения.

Коды ошибок Ricoh Aficio SP150

  • код ошибки SC101 Exposure lamp error
  • код ошибки SC120 Scanner home position error 1
  • код ошибки SC121 Scanner home position error 2
  • код ошибки SC122 Scanner home position error 3
  • код ошибки SC123 Scanner home position error 4
  • код ошибки SC192 Automatic SBU adjustment error
  • код ошибки SC194 IPU White Level Detection Error
  • код ошибки SC302 Charge roller current leak
  • код ошибки SC320 Polygon motor error
  • код ошибки SC321 No laser start signal (F-GATE error)
  • код ошибки SC322 Laser synchronization error
  • код ошибки SC324 LD drive current over
  • код ошибки SC390 TD sensor error 1
  • код ошибки SC391 Development bias leak
  • код ошибки SC392 TD sensor initial setting error
  • код ошибки SC401 Transfer roller leak error 1
  • код ошибки SC402 Transfer roller leak error 2
  • код ошибки SC411 Separation bias leak error
  • код ошибки SC500 Main motor lock
  • код ошибки SC501 1st paper tray lift motor malfunction
  • код ошибки SC502 2nd paper tray lift motor malfunction
  • код ошибки SC503 3rd paper tray lift motor malfunction (optional paper tray unit)
  • код ошибки SC504 4th paper tray lift motor malfunction (optional paper tray unit)
  • код ошибки SC506 Paper tray unit main motor lock (optional paper tray unit only)
  • код ошибки SC507 Tandem tray lift error (optional LCT)
  • код ошибки SC508 Rear fence drive error (optional LCT)
  • код ошибки SC509 Side fence drive error (optional LCT)
  • код ошибки SC541 Fusing thermistor open
  • код ошибки SC542 Fusing temperature warm-up error
  • код ошибки SC543 Fusing overheat error
  • код ошибки SC544 Fusing low temperature error
  • код ошибки SC546 Unstable fusing temperature
  • код ошибки SC547 Zero cross signal malfunction
  • код ошибки SC590 Exhaust fan motor error
  • код ошибки SC610 Communication error between IOB and duplex unit
  • код ошибки SC620 Communication error between IOB and ADF
  • код ошибки SC691 Communication error between BICU and fax controller
  • код ошибки SC692 Communication error between BiCU and printer controller
  • код ошибки SC694 Communication error between BICU and scanner controller
  • код ошибки SC696 Communication error between IOB and finisher
  • код ошибки SC722 Finisher jogger motor error
  • код ошибки SC725 Finisher stack feed-out motor error
  • код ошибки SC726 Finisher shift motor error
  • код ошибки SC730 Finisher stapler position motor error
  • код ошибки SC733 Finisher stack feed-out motor error
  • код ошибки SC734 Finisher lift motor error
  • код ошибки SC735 Finisher exit guide plate motor error
  • код ошибки SC750 Intp2ange unit connection error
  • код ошибки SC751 Bridge unit connection error
  • код ошибки SC752 Finisher connection error
  • код ошибки SC760 ADF gate abnormal
  • код ошибки SC770 Shift tray motor error (optional shift tray unit)
  • код ошибки SC900 Total counter error
  • код ошибки SC901 Mechanical Total Counter
  • код ошибки SC921 MSU hardware error
  • код ошибки SC980 Program loading error
  • код ошибки SC981 NVRAM clear error
  • код ошибки SC990 Communication error between BICU and IOCSS board
  • код ошибки SC999 Program version error

Коды ошибок Aficio MP C2010, 2050, 2070

  • E1 Exposure lamp
  • E2 Scan
  • E5 Fuser
  • E6 Drive
  • E7 Master
  • E8 Exp. Lamp heater/Exp. Lamp thermistor of thermofuse
  • E9 Optics board
  • EA Interface — sorter

Коды ошибок Ricoh Aficio FT-3013, 3213  

  • 11 Exposure lamp open
  • 12 Exposure lamp stays on
  • 12 Zero cross. Main board or DC power supply
  • 21 Scan home problem (did not return home)
  • 22 Scan home problem (did not leave home)
  • 28 Lens home problem (did not get home)
  • 29 Lens home problem (did not leave home)
  • 2A Mirror home problem (did not get home)
  • 2B Mirror home problem (did not leave home)
  • 40 Optics thermistor open
  • 52 Low fuser temperature. Lamp, thermal switch, thermistor
  • 53 High fuser temperature. Themistor, AC driver, pinched wire
  • 55 Fuser thermistor open
  • 70 Waste toner. 80K copies or 9 toner cartridges have been run. Reset with SP mode 83
  • 96 Document feeder drive problem
  • U2 User code. Key counter not installed

Коды ошибок Ricoh FT3020, 3050, 3060

  • E1 Scanner of Exp. Lamp
  • E2 Main drive or relay RA2
  • E3 Fuser
  • E4 Total counter
  • U1 Interlock or thermal fuse
  • U2 Key counter
  • U3 Oil (later machines)

Коды ошибок Ricoh FT3320

  • E1 Exposure lamp
  • E2 Scan problem
  • E5 Fuser
  • E6 Drive
  • E7 Toner waste is full
  • U3 Developer unit is not installed
  • U5 Add fuser oil

Коды ошибок Ricoh 3513, 3713

  • 11 Exposure lamp open
  • 12 Exposure lamp stays on
  • 21 Scan home problem
  • 22 Scan home problem (did not return home)
  • 28 Lens home problem (did not get home)
  • 29 Lens home problem (did not leave home)
  • 2A Mirror home problem (did not get home)
  • 2B Mirror home problem (did not leave home)
  • 40 Optics thermistor open
  • 52 Low fuser temperature. Lamp, thermal switch, thermistor
  • 53 High fuser temperature. Thermistor, AC driver, pinched wire
  • 54 Fuser low temperature on early EPROM
  • 55 Fuser thermistor open

Коды ошибок Ricoh 4015

 

  • E11 Exposure lamp problem
  • E12 Exposure lamp problem
  • E13 Zero cross. Main board or power supply board
  • E14 Same as E13
  • E21 Scan home problem
  • E22 Scan home problem
  • E28 Lens home sensor
  • E29 Lens home problem
  • E2A 4th & 5th mirror home problem
  • E2B 4th & 5th mirror home problem. Fuse 2 on AC/DC board
  • E40 Optics thermistor
  • E42 Bad transfer corona or HVT
  • E52 Low fuser temperature
  • E53 High fuser temperature
  • E54 Fuser lamp on too long
  • E55 Fuser thermistor open
  • U1 Right side open
  • U2 No key counter
  • U4 Sorter not latched, not closed
  • U6 Developer unit not in place

Коды ошибок Ricoh FT-4022, 4027

  • C1 Front door open
  • C2 Exit door
  • C3 Cassette cover
  • C4 LCT cover
  • C5 Sorter open or not latched to machine, or fuse 304 on DC power board
  • C6 ADF cover
  • C7 Right side cover
  • E101 Exposure lamp too long
  • E103 Frequency problem
  • E120, 121 Scan home problem
  • E124 Scan drive problem
  • E140 Lens home, or fuse 303 on DC board
  • E141-143 Lens home sensor, fuse 303 on DC board
  • E144, 145 Mirror sensor, fuse 303 on DC board
  • E191 Image density sensor error
  • E302 Charge roller problem or HVT problem
  • E346 Bias loss
  • E351 Image density sensor problem
  • E352 TD sensor error
  • E353 Vsp problem. Dirty or bad image density sensor
  • E354 Vsg problem. Same as E353
  • E355 Toner density sensor problem
  • E356 Same as 355
  • E405 Transfer belt or charge roller drive
  • E440 Main drive
  • E442 Drum charge thermistor
  • E501 Upper lift motor
  • E502 Lower lift motor
  • E503 1st tray motor
  • E504 2nd tray motor
  • E505 3rd tray motor
  • E506 Tray main motor drive problem
  • E507 LCTl lift motor
  • E522-525 Jogger sensor
  • E541 Fuser thermistor
  • E542 Fuser temperature too low
  • E543 Fuser temperature too high
  • E544 Fuser temperature too high
  • E547 Fuser lamp won't shut off
  • E548 Fuser temperature too high or too low
  • E620 Communication problem between main board and ARDF
  • E621 Communication problem between main board and sorter
  • E623 Communication problem between main board and paper trays
  • E720 Sorter stapler timing roller sensor
  • E721 Sorter stapler bin lift sensor
  • E722 Sorter stapler jogger sensor
  • E723 Sorter stapler grip sensor
  • E724 Sorter stapler error
  • E900, 901 Copy counter
  • U2 Key counter
  • U6 Fuser unit not installed properly
  • U7 Duplex unit

Коды ошибок Ricoh FT-4065

  • E1 Exposure lamp
  • E2 Lamp relay
  • E3 Registration start switch
  • E4 Scan not home
  • E5 No home position
  • E6 lens home switch not on
  • E7 Lens home switch off
  • E8, E9 Encoder
  • EA Thermofuse
  • Eb Thermistor
  • EC Not ready
  • Ed Pulse generator
  • EE Total counter
  • EF Optics

Коды ошибок Ricoh FT-4085

  • 11 Exposure lamp
  • 12 Lamp relay
  • 20 Low frequency encoder output
  • 21 Scan
  • 23 No registration start signal
  • 24 No home position
  • 28 Lens home position not on
  • 29 Lens home position not off
  • 52 Thermofuse
  • 53 Thermistor
  • 54 Not ready
  • 61 Pulse generator
  • 91 Total counter
  • 93 Interface

Коды ошибок Ricoh FT-4215, 4220, 4222

  • E11 Exposure lamp problem
  • E12 Exposure lamp problem
  • E13 Zero cross
  • E21, 22 Scan home problem. Fuse 102 on DC power supply
  • E28, 29 Lens home problem
  • E2A 4th & 5th mirror home problem. Fuse 101 on DC power supply
  • E2B 4th & 5th mirror home problem
  • E52 Low fuser temperature
  • E53 High fuser temperature
  • E55 Fuser thermistor open
  • E70 Waste toner full
  • E80 Communication problem between copier and duplex unit. Fuse 100 or 101 on DC power supply bored
  • E82, 83 Jogger home problem
  • U1 Right side open
  • U2 No key counter
  • U4 Sorter not latched or not closed
  • U5 Cassette lift sensor
  • U7 Duplex open

Коды ошибок Ricoh 4400

  • 11 Exposure lamp
  • 12 Exposure lamp stays on
  • 21, 22 Scan not home
  • 23 No signal from registration switch
  • 24 Scan not home
  • 25 Scan
  • 28 Lens not home
  • 29 Lens won't leave home
  • 2A Second scan sensor
  • 2A Mirror sensor stays actuated
  • 2B Mirror sensor stays actuated
  • 2B Scan sensor
  • 2C Scanner moving too fast
  • 2D Scanner moving too slowly or not moving
  • 31 Drum thermistor
  • 32 Toner sensor
  • 41 Third cassette lift motor sensor
  • 52 Fuser thermofuse
  • 53 Fuser thermistor
  • 54 Low temperature at warm up
  • 55 High temperature at warm up
  • 56 Low temperature after warm up
  • 61 Pulse generator
  • 81, 82 Duplex jogger
  • 82 Duplex jogger
  • 91 Counter
  • 93 Main board

Коды ошибок Ricoh 4410

  • 11 Exposure lamp
  • 21 Scan not home
  • 23 No signal from regulator switch
  • 24 Scan not home
  • 28 Lens not home
  • 29 Lens won't leave home
  • 2A Second scan flasher
  • 2B Scan sensor
  • 2C Scanner moving too fast
  • 2D Scanner moving too slowly
  • 31 Drum thermistor
  • 32 Toner sensor
  • 41 Third cassette lift motor sensor
  • 53 Fuser thermistor
  • 54 Low temperature at warm up
  • 55 High temperature at warm up
  • 56 Low temperature after warm up
  • 61 Pulse generator
  • 91 Counter
  • 93 Main board

Коды ошибок Ricoh 4420

  • E1 Exposure lamp
  • E2 Lamp relay
  • E3 Registration start switch
  • E4 Scan not home
  • E5 No home position
  • E6 lens home switch not on
  • E7 Lens home switch off
  • E8, E9 Encoder
  • EA Thermofuse
  • Eb Thermistor
  • EC Not ready
  • Ed Pulse generator
  • EE Total counter
  • EF Optics

Коды ошибок Ricoh 4421

  • 21, 22 Scanner home position error
  • 28, 29 Lens home position error
  • 2A, 2B 4th/5th mirror home position error

Коды ошибок Ricoh FT4430, 4460, 4480, 4490

  • 11 Exposure lamp
  • 21 Scan not home
  • 23 No signal from regulator switch
  • 24 Scan not home
  • 28 Lens not home
  • 29 Lens won't leave home
  • 2A Second scan flasher
  • 2B Scan sensor
  • 2C Scanner moving too fast
  • 2D Scanner moving too slowly
  • 31 Drum thermistor
  • 32 Toner sensor
  • 41 Third cassette lift motor sensor
  • 53 Fuser thermistor
  • 54 Low temperature at warm up
  • 55 High temperature at warm up
  • 56 Low temperature after warm up
  • 61 Pulse generator
  • 91 Counter
  • 93 Main board

Коды ошибок Ricoh 4522, 4527

  • C1 Front door open
  • C2 Exit door
  • C3 Cassette cover
  • C4 LCT cover
  • C5 Sorter open or not latched to machine, or fuse 304 on DC power board
  • C6 ADF cover
  • C7 Right side cover
  • E101 Exposure lamp too long
  • E103 Frequency problem
  • E120, 121 Scan home problem
  • E124 Scan drive problem
  • E140-143 Lens home, or fuse 303 on DC board
  • E144, 145 Mirror sensor, fuse 303 on DC board
  • E191 Image density sensor error
  • E302 Charge roller problem or HVT problem
  • E346 Bias loss
  • E351 Image density sensor problem
  • E352 TD sensor error
  • E353, 354 Vsp problem. Dirty or bad image density sensor
  • E355, 356 Toner density sensor problem
  • E405 Transfer belt or charge roller drive
  • E440 Main drive
  • E442 Drum charge thermistor
  • E501 Upper lift motor
  • E502 Lower lift motor
  • E503 1st tray motor
  • E504 2nd tray motor
  • E505 3rd tray motor
  • E506 Tray main motor drive problem
  • E507 LCTl lift motor
  • E522-525 Jogger sensor
  • E541 Fuser thermistor
  • E542 Fuser temperature too low
  • E543 Fuser temperature too high
  • E544 Fuser temperature too high
  • E547 Fuser lamp won't shut off
  • E548 Fuser temperature too high or too low
  • E620 Communication problem between main board and ARDF
  • E621 Communication problem between main board and sorter
  • E623 Communication problem between main board and paper trays
  • E720 Sorter stapler timing roller sensor
  • E721 Sorter stapler bin lift sensor
  • E722 Sorter stapler jogger sensor
  • E723 Sorter stapler grip sensor
  • E724 Sorter stapler error
  • E900, 901 Copy counter
  • U2 Key counter
  • U6 Fuser unit not installed properly
  • U7 Duplex unit

Коды ошибок Ricoh Aficio MP C5000, 5010

  • 11 Exposure lamp
  • 12 Exposure lamp relay
  • 21-24 Scan
  • 25 Scan motor
  • 28 Lens position
  • 2A, 2B 2nd scan home
  • 2C, 2D Scan motor
  • 2E Encoder
  • 31 Drum thermistor
  • 43 Lower paper feed
  • 52 Thermofuse
  • 53 Thermistor
  • 54 No heat
  • 55 Overheat
  • 61 Drive system
  • 81, 82 Jogger problem
  • 91 Counter
  • 93 Optics and main board interface
  • 94 Optics board and main board interface

Коды ошибок Ricoh ft5035, 5535

  • C1 Front door open
  • C2 Exit door
  • C3 Cassette cover
  • C4 LCT cover
  • C5 Sorter open or not latched to machine, or fuse 304 on DC power board
  • C6 ADF cover
  • C7 Right side cover
  • E101 Exposure lamp on too long
  • E103 Frequency problem
  • E120, 121 Scan home problem
  • E124 Scan drive problem
  • E140-143 Lens home, or fuse 303 on DC board
  • E144, 145 Mirror sensor, fuse 303 on DC board
  • E191 Image density sensor problem
  • E302 Charge roller problem or HVT problem
  • E346 Bias loss
  • E351 Image density sensor error
  • E352 TD sensor error
  • E353, 354 Vsp problem. Dirty or bad image density sensor
  • E355 Toner density sensor problem
  • E356 Vsp problem. Dirty or bad image density sensor
  • E405 Transfer belt or charge roller drive
  • E440 Main drive
  • E442 Drum charge thermistor
  • E501 Upper lift motor
  • E502 Lower lift motor
  • E503 1st tray motor
  • E504 2nd tray motor
  • E505 3rd tray motor
  • E506 Tray main motor drive problem
  • E507 LCT lift motor
  • E522-525 Jogger sensor
  • E541 Fuser thermistor
  • E542 Fuser temperature too low
  • E543 Fuser temperature too high
  • E544 Fuser temperature too high
  • E547 Fuser lamp won't shut off
  • E548 Fuser temperature too high or too low
  • E620 Communication problem between main board and ARDF
  • E621 Communication problem between main board and sorter
  • E623 Communication problem between main board and paper trays
  • E720 Sorter stapler timing roller sensor
  • E721 Sorter stapler bin lift sensor
  • E722 Sorter stapler jogger sensor
  • E723 Sorter stapler grip sensor
  • E724 Sorter stapler error
  • E900, 901 Copy counter
  • U2 Key counter
  • U6 Fuser unit not installed properly
  • U7 Duplex unit

Коды ошибок Ricoh 5050, 5070

  • 11 Exposure lamp
  • 12 Exposure lamp relay
  • 21-24 Scan
  • 28 Lens position
  • 29 Lens
  • 2A-2D Scan
  • 41 Upper paper feed
  • 43 Lower paper feed
  • 52 Thermofuse
  • 53 Thermistor
  • 54 No heat
  • 61 Drive
  • 81 Jogger
  • 91 Counter
  • 93 Main board or optics

Коды ошибок Ricoh 5540

  • 11 Exposure lamp
  • 12 Exposure lamp stays on
  • 21 Scan not home
  • 22 Scan not home
  • 23 So signal from registration switch
  • 24 Scan not home
  • 25 Scan
  • 28 Lens not home
  • 29 Lens won't leave home
  • 2A Second scan sensor
  • 2A Mirror sensor stays actuated
  • 2B Mirror sensor stays actuated
  • 2B Scan sensor
  • 2C Scanner moving to fast
  • 2D Scanner moving too slowly or not moving
  • 31 Drum thermistor
  • 32 Toner sensor
  • 41 Third cassette lift motor sensor
  • 52 Fuser thermofuse
  • 53 Fuser thermistor
  • 54 Low temperature at warm up
  • 55 High temperature at warm up
  • 56 Low temperature after warm up
  • 61 Pulse generator
  • 81 Duplex jogger
  • 82 Duplex jogger
  • 91 Counter

Коды ошибок Ricoh 5560

  • 11 Exposure lamp
  • 12 ExpExposure lamp relay
  • 21 Scan home switch not actuated
  • 22 Scan home switch activated
  • 23 Scan registration switch
  • 24 Scan home problem
  • 25 Scan motor
  • 28 Lens home switch not actuated
  • 29 Lens home switch actuated
  • 2A 2nd scan home switch not actuated
  • 2b 2nd home scan switch actuated
  • 2c Encoder (high frequency)
  • 2d Encoder (low frequency)
  • 2E No encoder
  • 31 Drum thermistor
  • 52 Fuser thermofuse (or F3)
  • 53 Fuser thermistor
  • 54 No ready
  • 55 High temperature
  • 61 Pulse generator
  • 81 Jogger home switch not actuated
  • 82 Jogger home switch actuated
  • 91 Total counter
  • 94 Data transfer problem between main board and operations board

Коды ошибок Ricoh 5632, 5732, 5832, 5840

  • C1 Front door open
  • C2 Exit door
  • C3 Cassette cover
  • C4 LCT cover
  • C5 Sorter open/not latched to machine
  • C6 ADF cover
  • C7 Right side cover
  • E101 Exposure lamp on too long
  • E103 Frequency problem
  • E120, 121 Scan home problem
  • E124 Scan drive problem
  • E140-143 Lens home, or fuse 303 on DC board
  • E144, 145 Mirror sensor, fuse 303 on DC board
  • E191 Image density sensor problem
  • E302 Charge roller or HVT problem
  • E346 Bias loss
  • E351 Image density sensor problem
  • E352 TD sensor error
  • E353, 354 Vsp problem
  • E355, 356 Toner density sensor problem
  • E405 Transfer belt or charge roller drive
  • E440 Main drive
  • E442 Drum charge thermistor
  • E501 Upper lift motor
  • E502 lower lift motor
  • E503 1st tray motor
  • E504 2nd tray motor
  • E505 3rd tray motor
  • E506 Tray main motor drive problem
  • E507 LCT lift motor
  • E522-525 Jogger sensor
  • E541 Fuser thermistor
  • E542 Fuser temperature too low
  • E543 Fuser temperature too high
  • E544 Fuser temperature too high
  • E547 Fuser lamp won't shut off
  • E548 Fuser temperature too high or too low
  • E620 Communication problem between main board and ARDF
  • E621 Communication problem between main board and sorter
  • E623 Communication problem between main board and paper trays
  • E720 Sorter stapler timing roller sensor
  • E721 Sorter stapler bin lift sensor
  • E722 Sorter stapler jogger sensor
  • E723 Sorter stapler grip sensor
  • E724 Sorter stapler error
  • E900, 901 Copy counter
  • U2 Key counter
  • U6 Fuser unit not installed properly
  • U7 Duplex unit

Коды ошибок Ricoh 6080, 6085

  • 1 Exposure lamp
  • 10 Scanner velocity
  • 11 Scanner return
  • 12 Total counter
  • 13 Corona problem
  • 2 Drum thermistor
  • 3 Drum heater
  • 4 Drum overheat
  • 5 Fuser thermistor
  • 6 Fuser lamp
  • 7 Fuser overheat
  • 8 Optics encoder
  • 9 Scanner home

Коды ошибок Ricoh 6620

  • 11 Exposure lamp
  • 12 Exposure lamp stays on
  • 21, 22 Scan not home
  • 23 So signal from registration switch
  • 24 Scan not home
  • 25 Scan
  • 28 Lens not home
  • 29 Lens won't leave home
  • 2A Second scan sensor
  • 2A Mirror sensor stays actuated
  • 2B Scan sensor
  • 2C Scanner moving to fast
  • 2D Scanner moving too slowly or not moving
  • 31 Drum thermistor
  • 32 Toner sensor
  • 41 Third cassette lift motor sensor
  • 52 Fuser thermofuse
  • 53 Fuser thermistor
  • 54 Low temperature at warm up
  • 55 High temperature at warm up
  • 56 Low temperature after warm up
  • 61 Pulse generator
  • 81, 82 Duplex jogger
  • 91 Counter
  • 93 Main board

Коды ошибок Ricoh 6645, 6655, 6665

  • 101 Exposure lamp
  • 103 Power frequency problem
  • 104 Exposure lamp
  • 120 Scanner home problem
  • 121 Scan home problem
  • 125 Scanning too slow
  • 126 Scanning too fast
  • 127 Scan drive problem or encoder
  • 140 Lens home problem (vertical)
  • 141 Lens home problem (vertical)
  • 142 Lens home problem (horizontal)
  • 143 Lens home problem (horizontal)
  • 144 3rd scan sensor problem
  • 145 3rd scan sensor problem
  • 146 Magnification problem
  • 190 Optics thermistor open circuit
  • 191 Scan motor thermistor
  • 302 Charge corona short
  • 303 Charge corona cleaner problem
  • 341 Developer motor drive problem
  • 342 Toner disposal motor drive problem
  • 343 Vsp. Problem. Image density sensor problem
  • 351 Vsg. Problem. Higher than 4.3 volts. Image density sensor problem
  • 352 Toner sensor problem during developer calibration
  • 353 Vsp Problem. Image density sensor, drum bias or HVT
  • 354 Vsg Problem. Image density sensor, drum bias or HVT
  • 355 Toner density sensor problem. Vtd problem. Undertoned
  • 356 Toner density sensor problem. Vtd problem. Overtoned
  • 357 Vsp problem. Image density sensor, drum
  • 358 Vsp problem. Image density sensor, drum, toner dust
  • 361 Drum potential sensor calibration during process control setup
  • 364 Vd problem. Drum potential sensor, drum or charge corona
  • 365 V1 problem. Drum potential sensor, drum, charge corona, dirty optics
  • 402 Transfer, transfer belt, HVT
  • 440 Main motor speed problem
  • 442 Drum thermistor
  • 500 Bypass feed
  • 501 Paper feed motor
  • 502 1st lift motor
  • 503 2nd lift motor
  • 504 3rd lift motor
  • 506 LCT motor
  • 507 LCT feed motor
  • 508 Tandem fence motor
  • 510 Tandem side home sensor
  • 511 Tandem side home sensor
  • 520 Duplex/fuser drive motor problem
  • 522 Jogger home sensor
  • 523 Jogger home sensor
  • 541 Fuser thermistor
  • 542 Fuser does not warm-up
  • 543 Fuser temperature too high. Monitored by main board
  • 544 Fuser temperature too high. Monitored by optics board
  • 545 Low fuser temperature. Monitored by main board
  • 546 Low fuser temperature. Monitored by optics board
  • 547 Fuser lamp won't shut off
  • 548 Erratic fuser temperature
  • 600 Communication problem between main board and operation board
  • 601 Communication problem between main board and optics board
  • 602 Communication problem between main board and high voltage unit
  • 603 Main board problem
  • 620 Communication problem between main board and document feeder boards
  • 621 Communication problem between main board and sorter staplers or finisher
  • 700 DJF/RDH feed motor
  • 701 DJF/RDH transport belt problem
  • 702 DJF exit or RDH inverter motor
  • 703 RDH exit motor problem
  • 730 Sorter/stapler or finisher transport motor
  • 731 Bin lift motor
  • 732 Tray shift motor
  • 733 Tray shift lift motor
  • 735 Duplex jogger motor
  • 737 Gripper motor
  • 738 Staple motor
  • 740 Staple drive motor
  • 741 Bin rear plate motor (stapler)
  • 742 Finisher stack feed motor
  • 900 Total counter
  • 901 Total counter
  • код ошибки SC Full waste toner bottle. Technician must empty this. Emptying the waste toner and reinstalling the bottle will clear this code

Коды ошибок Ricoh 6750

  • 11 Exposure lamp
  • 13 Exposure lamp
  • 14 Electrical frequency problem
  • 21, 22 Scan problem
  • 24 Scan home problem
  • 25 Scan drive motor problem
  • 26 Scan problem during simulation V1 adjustment (SP mode 67)
  • 27 Scan problem during simulation
  • 28, 29 Lens home problem
  • 2A, 2B Mirror home sensor
  • 2D Scan drive problem or fuse 5 on optics board
  • 31 Drum thermistor
  • 41 Tray lift
  • 42 2nd tray lift
  • 43 3rd tray lift
  • 53 Fuser thermistor problem
  • 54 Fuse temperature low
  • 55 Fuser temperature too high
  • 56 Fuser temperature low
  • 57 Fuser lamp on too long
  • 58 Fuser temperature erratic
  • 61 Main drive problem, or fuse 1 or fuse 6 on main motor board
  • 62 Developer drive problem, or fuse 1 on developer motor drive board
  • 81, 82 Duplex jogger home sensor
  • 85, 86 Charge corona cleaner problem
  • 87 Transfer/separator corona cleaner unit not working
  • 88 Transfer/separator corona cleaner unit not home
  • 91 Total counter
  • B1 Sorter shift tray
  • B2 Sorter shift motor
  • B3 Sorter shift tray up/down motor
  • B4 Stapler transport motor
  • B5 Stapler lift motor
  • B6 Stapler drive motor
  • B7 Stapler jogger motor
  • B8 Stapler motor

Коды ошибок Ricoh M10

  • E1 Exposure lamp
  • E2 Scan
  • E5 Fuser
  • E6 Drive
  • E7 Master not turning
  • E8 Lamp heater (exposure)

В случае появления серьезной неисправности принтера или МФУ Ricoh, мы не рекомендует проводить ремонт аппарата самостоятельно, а советуем обратиться в наш сервисный центр Прионта, и доверить ремонт вашего аппарата нашим квалифицированным мастерам.

Возврат к списку